D13.C.5 Member Selection and Code Check
Both code checking and member selection options are available in SP 16.13330.2011.
Output of selection and check results are given in suppressed, extended and advanced forms. Form of output results depends on value of parameter TRACK.
Results are presented in tables. Three versions of output results are possible: suppressed – results according the critical strength condition (TRACK=0), extended - results according to all check conditions (TRACK=1) and advanced – complete information on results of member design (TRACK=2).
- (TRACK=2)
- number of member;
- type and number of cross-section;
- result obtained (ACCEPTED – requirements are met, FAILURE – are not met);
- abbreviated name of normative document (code, standard) (SNiP);
- number of check clause;
- safety of strength (ratio between design and normative values);
- number of the most unfavorable loading;
- value of longitudinal force acting in the member with subscript indicating its direction (C – compression, P – tension);
- bending moments in relation to local member axes Z and Y;
- distance to section, in which the most unfavorable combination of forces acts.
コードチェックの一般的な情報については、「 D1.B.1.3 Code Checking」を参照してください。コードチェックコマンドの仕様の詳細については、「TR.49 コードチェックの設定」を参照してください。
メンバー選択の一般的な情報については、「 D1.B.1.4 Member Selection」を参照してください。メンバー選択コマンドの仕様の詳細については、「TR.49.1 メンバー選定の設定」を参照してください。
D13.C.5.1 Example of TRACK 0 output
In suppressed form (TRACK 0) results are presented according to the critical check for given member with indication of SP 16 clause number, according to which strength safety of the member is minimum.
ALL UNITS ARE - KN METE ======================================================================== MEMBER CROSS RESULT/ CRITICAL COND/ RATIO/ LOADING/ SECTION NO. FX MZ MY LOCATION ======================================================================== 2 I IPE300 PASS SNiP- 8.4.1 0.76 1 0.000E+00 -4.446E+01 0.000E+00 4.000E+00
D13.C.5.2 Example of TRACK 1 output
In extended form (TRACK 1) results are presented on the basis of all required by SP 16 checks for given stress state.
ALL UNITS ARE - KN METE ======================================================================== MEMBER CROSS RESULT/ CRITICAL COND/ RATIO/ LOADING/ SECTION NO. FX MZ MY LOCATION ======================================================================== 2 I IPE300 PASS SNiP- 8.2.1 0.22 1 0.000E+00 -4.446E+01 0.000E+00 4.000E+00 2 I IPE300 PASS SNiP- 8.2.1 0.00 1 0.000E+00 -4.446E+01 0.000E+00 4.000E+00 2 I IPE300 PASS SNiP- 8.2.1 0.20 1 0.000E+00 -4.446E+01 0.000E+00 4.000E+00 2 I IPE300 PASS SNiP- 8.4.1 0.76 1 0.000E+00 -4.446E+01 0.000E+00 4.000E+00
D13.C.5.3 Example of a TRACK 2 output
In advanced form (TRACK=2) in addition to tabled results supplementary information is presented.
- Material characteristics:
- Steel;
- Design resistance;
- Elasticity modulus;
- Section characteristics:
- Length of member;
- Section area;
- Net area;
- Inertia moment (second moment of area) (I);
- Section modulus (W);
- First moment of area (S);
- Radius of gyration;
- Effective length;
- Slenderness;
- Results are presented in two columns, Z and Y respectively.
- Design forces:
- Longitudinal force;
- Moments;
- Shear force.
Signs + and - indicate direction of acting longitudinal force, bending moments and shear forces in accordance with sign rules assumed in program STAAD.
Check results in advanced form are presented with values of intermediate parameters by formulas in analytical and numerical expression with indication of SNiP clause.
ALL UNITS ARE - KN METE ======================================================================== MEMBER CROSS RESULT/ CRITICAL COND/ RATIO/ LOADING/ SECTION NO. FX MZ MY LOCATION ======================================================================== 2 I IPE300 PASS SNiP- 8.2.1 0.22 1 0.000E+00 -4.446E+01 0.000E+00 4.000E+00 2 I IPE300 PASS SNiP- 8.2.1 0.00 1 0.000E+00 -4.446E+01 0.000E+00 4.000E+00 2 I IPE300 PASS SNiP- 8.2.1 0.20 1 0.000E+00 -4.446E+01 0.000E+00 4.000E+00 2 I IPE300 PASS SNiP- 8.4.1 0.76 1 0.000E+00 -4.446E+01 0.000E+00 4.000E+00 MATERIAL DATA Steel =S355 EN10025-2 Modulus of elasticity = 206.E+06 kPa Design Strength (Ry) = 355.E+03 kPa SECTION PROPERTIES (units - m) Member Length = 8.00E+00 Gross Area = 5.38E-03 Net Area = 5.38E-03 z-axis y-axis Moment of inertia (I) : 836.E-07 604.E-08 Section modulus (W) : 557.E-06 805.E-07 First moment of area (S) : 314.E-06 625.E-07 Radius of gyration (i) : 125.E-03 335.E-04 Effective Length : 160.E-01 800.E-02 Slenderness : 0.00E+00 0.00E+00 DESIGN DATA (units -kN,m)SNiP II-23-81*/2011 Axial force : 0.00E+00 z-axis y-axis Moments : -445.E-01 0.00E+00 Shear force : 0.00E+00 0.00E+00 Bi-moment : 0.00E+00 Value of Bi-moment not being entered!!! CRITICAL CONDITIONS FOR EACH CLAUSE CHECK F.(41) M/(Wn,min*Ry*GAMAc)=-444.6E-01/( 5.57E-04* 355.0E+03* 1.00E+00= 2.25E-01=<1 F.(44) 0.87/(Ry*GAMAc)*SQRT(SIGMz^2+3*TAUzy^2)= 0.87/( 355.0E+03* 1.00E+00)*SQRT(-798.2E+02^2+3* 0.000E+00)= 1.96E-01=<1 TAUzy/(Rs*GAMAc)= 0.000E+00/( 205.9E+03* 1.00E+00)= 0.00E+00=<1 F.(69) M/(FIb*Wcx*Ry*GAMAc)= -444.6E-01/( 2.97E-01* 5.57E-04* 355.0E+03* 1.00E+00)= 2.25E-01=<1
Conventional notations assumed in presentation of results: +, -, /, *,**, SQRT, their respective meanings (i.e., addition, subtraction, division, multiplication, raising to the second power (squared), and square root). Conventional notations of stresses, coefficients and characteristics of steel resistance comply with accepted in the SP standard. Only Greek letters are changed by their names (e.g., , γc-GAMAC; α-ALPHA; β-BETA, η-ETA, φ-PHI, etc.).